How To Build A Bluebird House

First thing you need to do is measure 10 38 from the start of the 4 board. Back should hang about an inch below the bottom.

Creating Bluebird Habitat Free Bluebird House Plans

The hole needs to be 5½ inches from the bottom of the front board.

How to build a bluebird house. No hardware to buy and easy to clean outPlease do not download and re-upload this video. Pre-drill holes and attach the front D to the floor A and side B. Assemble back sides roof and bottom using nails.

This is a quick how-to video on building an Eastern Bluebird house. Thin bark strips pine needles and dry grasses are typical nesting materials. For a round entrance hole eastern bluebird boxes should be 1 12 inches in diameter and 1 916 inches for mountain and western bluebirds.

Drill three holes two in the front one in the back through the front and back walls and into the side of the door. Drill a 1-12-inch entrance hole in the front piece with a spade bit for eastern and western bluebirds. The bluebird house plans below show how the pieces fit together.

Using the chisel cut deep crisscross scratches on the inside of the front panel. Cut the entry hole by drilling two overlapping holes with a 1-38- in. Pre-drill holes and attach one of the sides B to the floor using 2 finishing nails.

To determine the angle of the cut measure up 10-12 from one end and make a mark. Once the sides were attached my Dad and Emanuelle used the drill press to drill holes for the bluebirds to enter the bird houses. Bluebirds and other species often use nest boxes for roosting in cold weather.

The best dimensions for bluebird houses are. 15 inches 156 inches for mountain bluebirds Entrance Height. All you need is a 6 foot dog ear fence picket 12-1 ¼ inch deck screws a 332 inch dril.

The pilot holes pre-drill holes Emanuelle made were the ones for when we would attach the bottoms to the body. To make one of the side pieces and the front of your bluebird house measure 2 8-inch pieces from your board and cut them off using a handsaw or a compound miter saw. A drill press is a pretty neat tool.

Line it up carefully at the saw and cut on the line. Bluebird House Plans Assembly Cut out all the birdhouse parts as shown on illustrations above. Measure and Cut Bluebird House Door The next step to build a bluebird house is to cut part D from a 14 so the end is 45 degrees and then reset your saw to cut the piece to final length.

The top edge of the sides part C are cut at a 22-degree angle to create the slope for attaching the oversized roof. For mountain bluebirds then use a rasp to even out the edges. Bluebird Birdhouse Plans Cut the sides base back and roof of the bluebird bird house to the sizes indicated in the drawings and assemble them together as shown in the diagrams using 16 gauge galvanized finish nails.

Step 2 Roof and Floor. Center the hole about 1-12 inches from the top of the board. This is a fast and easy way to make a BlueBird house.

This will make the second shorter side with enough room to pivot. At the end of the nesting season clean out the nest box one last time and make any needed repairs. Set the piece you just cut out aside and make another measurement at 10 38 on the long board and cut it out.

6 to 10 inches above the house floor. Cut the front of the box 5 wide and 10 34 long with an entrance hole a 1 12 hole for eastern bluebirds or western bluebirds and 1 916 hole where ranges for the two overlap with mountain bluebirds whose center is 2 from the top and 2 12 from each side. Cut the 10 x 4 front door section and drill a 1-12 entry hole centered 7 above the bottom of the door.

Measure and cut another piece from the board that is about 7 14 inches. Smooth the edges of the hole with sandpaper. A clamp in not necessary but can be helpful for keeping edges straight during assembly.

Spade bit 1-12 in. Bluebird house hole size. 5-by-5 inches to accommodate broods of five to eight chicks.

In areas where mountain bluebirds reside drill the entrance hole 1-916 inches. Insert two nails in the top as pivot nails one in the bottom to hold the side door closed. If you only have Eastern Bluebirds you can use a 1½ inch hole.

Female bluebirds build tight cup nests atop a looser built base. You should now have 2 10 38 pieces out of the 4 board. Lay Out the Pieces.

The most important element is getting the entrance hole size correct especially to eliminate larger pest birds such as starlings from using the box. Cut a 1-916 inch entry hole in the front section for the bluebird house to accommodate for all bluebird species. Fasten house to a 5-6 pole with metal tie straps.

This basic nest box is easy to build. Sides should be flush with the base of the bluebird house.

Eastern Bluebird Nest Box State Of Tennessee Wildlife Resources Agency